Please select your home edition
Edition
Upffront 2020 Foredeck Club SW LEADERBOARD

Martin Breaker - The Ejector Seat of Spinnaker Drops

by Aleix Escorsell 11 Nov 2022 04:00 PST
Martin Breaker - The Ejector Seat of Spinnaker Drops © upffront.com

What is a Martin Breaker?

The term Martin Breaker refers to a shackle tripping device to allow for remote release of a tack line under load during a spinnaker drop. There are a multitude of possible configurations and, like many things in sailing, the optimal setup will depend on the boat, the crew and a good bit of trial and error. In this article we aim to give a general overview of some of the things to look out for.

Etymology of Martin Breaker

We are familiar with the name Jack appearing in sailing terminology (Jackstay, Lazyjack etc), but 'Martin' is not common. The term Martin Breaker is widely used in racing circuits but perhaps less well known in the wider sailing community. It certainly doesn't seem to be a ye-olde nautical term that has filtered down through the generations. So where does it originate?

Surely Google, the fountain of all knowledge, will provide the answer. But no! A quick scour of the web does not reveal a conclusive etymology. Digging a bit further, discussions of remote release mechanisms can be found on several forums, sometimes with reference to the term Martin Breaker. Although the term might not be in universal lexicon, its validity is bolstered by appearing in the hardware offerings of manufacturers Tylaska and KZ.

One explanation can be seen on a forum post from 2006, stating that the tack release mechanism is named after ejection seat manufacturer Martin Baker. Is that so? It certainly seems plausible.

Blowing the Tack

Tripping the tack shackle under load is a popular method for initiating a spinnaker drop. Releasing the tack immediately depowers the kite and without the tackline attached there is nothing to slow down or hinder the process. Once the tack has gone, the kite can then be hauled down by a drop-line or the lazy sheet.

One option to release the shackle is to 'spike' it by hand. This usually involves the bow-person shimmying out to the end of the sprit and hanging on with one arm while jamming a spike into the shackle trigger with the other.

The alternative method is to rig a shackle release mechanism which is connected to a piece of Dyneema and led aft so the shackle can be tripped remotely. This is particularly useful for short-handed sailing where there are simply not enough people to leave one clinging to the end of the sprit during a drop.

The Trip Mechanism

Rigging a trip mechanism is a balance between making something that will release reliably but without being so sensitive that it can be triggered inadvertently.

Plug and Cone Fids

Tylaska produce a range of small fids which are designed specifically to trigger their snap shackles remotely. A full explanation can be found in our blog: Tylaska Cone and Plug Fids Explained.

Once primed, plug fids are probably the most sensitive option and will trigger easily. Hence they are also the most likely to trigger accidentally if knocked. Cone fids are less sensitive.

Remote Release Shackle

A recent addition to the Tylaska offering is a slight variation on the traditional snap shackle which includes 4m of thin Dyneema led through the spindle and connected to the trigger release.

This video from Tylaska shows more detail:

A dedicated remote release shackle like this is arguably the neatest solution. However, these are not currently widely available and incur a price hike of nearly 40% compared to the standard version.

Basic is Often Best

The third option is perhaps the simplest and easiest to implement. Simply pass a small soft shackle or loop of thin Dyneema through the snap shackle trigger. The release line can then be corrected to this loop.

Alternatively, pass a longer piece of Dyneema directly through the shackle so it forms a 2:1 with at least one end lead back to the foredeck.

This option is cheap to implement and can work with any trigger style snap shackle as long as the release mechanism is not too stiff. This is perhaps the least sensitive and care should be taken to ensure the release line passes across the correct end of the trigger, away from the pivot point.

Rigging a Martin Breaker

Whichever trip mechanism you choose, you then need to lead the release line back to the foredeck. Unless using a fid which is activated by pulling at right angles to the shackle, the release line should normally run parallel to the tackline to be most reliable. Run the release line through the bowsprit fitting and terminate on the foredeck.

The length of the release line depends a little on personal preference but should always have enough slack to allow for movement of the tackline through stretch or settling in the clutch. The release line can be made long enough so that the tack shackle can be brought back to the pulpit.

Once the release line is terminated, simply blow the tackline from the cockpit. The tackline runs free until the Martin Breaker snatches tight and trips the shackle. After the kite drop, remember to go forwards and collect the tackline which is now swinging freely off the end of the sprit.

Spend some time practising in manageable wind conditions to ensure you have an effective and reliable setup. A Martin Breaker can easily become a hazard if it trips inadvertently or worse still, won't trip when you need it to. But a well configured system can lead to clean and straightforward short-handed kite drops.

Super light winds can actually cause the most problems if there is not enough pressure in the kite to trip the shackle. A sharp tug on the foot of the kite will normally do the job.

Summary

The ejector seat of spinnaker drops, a Martin Breaker allows for remote triggering of your tack shackle to instantly de-power the kite for the take-down. As with any critical piece of kit, it is worth spending the time in practice and setup to get a good configuration that works for your boat and crew.

A well configured Martin Breaker will work 95% of the time and lead to clean, effective, low-stress drops. This can be a particularly good option for short handed sailors.

If you have any questions about these products, please feel free to contact us by mail at , or click the link below:

More Information

Related Articles

Spinnaker Snuffers - Better Than Furling?
upffront.com gives you the detailed answer A snuffer is a simple, reliable method of dousing an asymmetric spinnaker. Despite advances in furling technology, snuffers remain the first choice for many offshore race yachts such as Class 40 and IMOCA. Posted on 25 May
Discovering Ronstan
The ultimate introduction to quality and innovative solutions If there is one brand name that is synonymous with quality and innovative marine products specifically designed and engineered for sailors, it's Ronstan. This marque is renowned throughout the Sailing World. Posted on 19 May
Robline rope configurator
New customisable products from upffront.com even include splices Upffront.com recently added a range of Robline ropes to the configurable product range, allowing you to choose splicing options and purchase finished sheets and halyards directly online. Posted on 12 May
Jefa Autopilot Direct Drives - Simply the Best?
What makes up a good autopilot system and why the details matter The Jefa direct drives are something of a hallmark in autopilot drive engineering. Every aspect has been designed from the ground up to create an efficient, powerful and long-lasting pilot drive. Posted on 3 May
Adding a staysail?
Mast hardware options - a guide by upffront.com We have previously reported on the benefits of adding a staysail. But what about the mast fitting? For people looking to retrofit a staysail on a rig without an existing staysail sheave or tang, this can often be the crunch point. Posted on 27 Apr
The Importance of Teamwork in Sailing
upffront.com look at briefings, language and safety We cannot think of another sport where the importance of teamwork is so vital both before and during the actual event. Whether that event is a leisurely cruise or an ocean-going race. Posted on 19 Apr
Get Ready to Kedge
Anchoring for race yachts The practice of kedging has been used for hundreds of years as a method of manoeuvring or orienting a sailing vessel against tide and wind. A kedge anchor is typically smaller and lighter than the primary anchor, making it easier to handle. Posted on 12 Apr
Luff Foil versus Hanks
Which is best for you? upffront.com detail the considerations For racing yachts and cruiser/racers with a fixed (non-furling) headstay there are really two possible methods of attaching the luff of the jib to the wire or rod forestay: in a luff foil, or with hanks. Posted on 5 Apr
A Guide to Bowsprit Configuration
Carbon or aluminium, furling or non-furling, and what is needed to 'peel' A bowsprit is now an almost inevitable feature of a racing yacht or performance cruiser and there are also a number of off-the-shelf retrofit options available. The uptake is due in part to the popularity of asymmetric downwind sails. Posted on 29 Mar
Top Tips on How to Prep Your Boat for Spring
10 jobs that could easily be overlooked but are potentially critical Spring is approaching and we start to think about getting our boats ready for the coming season. Here is my list of ten jobs that could easily be overlooked but are potentially critical for you to enjoy a safe season ahead. Posted on 23 Mar
Upffront 2020 Foredeck Club SW FOOTER