Please select your home edition
Edition
Henri-Lloyd Dynamic Range

AC75 foil arm testing successfully carried out at Persico Marine

by America's Cup Media 17 May 2019 14:45 PDT
36th America's CupAC75 foil arms structure testing at Persico Marine © America's Cup

The second round of structural testing of the one design AC75 foil arms has successfully been conducted at Persico Marine in Italy this week.

Comprehensive tests were undertaken over the course of three days, with more than 100 different load cycles applied to the foil arm and were the final step in the foil arm design and construction process which has been led by Luna Rossa Challenge. The focus can now turn towards completing the production of the foil arms before they are distributed to the teams, in preparation for the respective launches of their AC75s in the coming months.

The satisfactory result follows on from the first round of one design foil arm testing undertaken at Persico in September 2018 after which a working group, with representatives of structural engineering from all of the teams to collaboratively redefine the design and build process for the one design foil arms for the AC75s.

The joint effort was led by Alessandro Franceschetti, Head of Structures for Luna Rossa Challenge together with New Zealand based composite engineering consultancy Pure Design and Engineering and Stefano Beltrando of Qi Composites who managed the quality control process.

During the testing, the one design foil arms were subjected to loads well in excess of twice those that are anticipated to be reached during intense AC75 racing.

"The one design foil arm is one of the primary structural components of the AC75. Today we achieved a great milestone towards the 36th America's Cup. This was a full-scale testing program, a 1:1 scale foil arm prototype was tested under specific critical load-cases to mimic and analyse its structural behavior under extreme conditions, such as high asymmetric loading and grounding scenarios. For the first time in America's Cup design programme history, a fully instrumented one design primary component has been tested to its full load carrying capacity until breakage. Today, we reached our targets and achieved all of our objectives, it was a synergic effort among all the teams," said Alessandro Franceschetti.

Representatives from the Challengers, the Defender Emirates Team New Zealand and relevant stakeholders were present at Persico for this important milestone.

Andrew Corkery of Pure Design and Engineering: "While the foil arms are one design components across all teams, the same challenges in managing this project have remained in balancing innovation and performance, with safety, reliability and cost efficiency. It is always a huge challenge to tick all of those boxes, but with the outcome of these tests now positive, we will look forward to judging the performance on the water in the near future."

Guillaume Verdier, Naval Architect, Emirates Team New Zealand: "Breaking foils in the America's Cup is not new, it happens when you are pushing the boundaries. We did this in the last campaign in Bermuda and it is never a quick fix, but these setbacks are recoverable as we have witnessed today and that's what the America's Cup is about."

Currently, the 8th foil arm is under construction at Persico, so the expectation is that the initial sets of foil arms will begin to ship to the teams in the coming weeks.

Marcello Persico, CEO of Persico Marine: "The America's Cup foil arm project is a unique opportunity for Persico, that no other company in the industry has had the opportunity to undertake. Our team at Persico has worked very hard with the Cup teams on the development of this project, the testing and to ensure that the one design foil arms are absolutely identical."

The other vital component to make the AC75s fly is the hydraulic and electronic foil cant system which was designed and built by Emirates Team New Zealand. The foil cant systems have already been dispatched and received by the teams.

Once the foil arms are received and subsequently installed, it will be all systems go for the launch of the first iterations of the AC75. The countdown to see these boats on the water is on.

To run the foil arm test, a bespoke test jig was been built in a secure area at Persico Marine. The set up allowed the 4.5m carbon foil arm to clamp on the cant axis point with a strop attached to a steel 'replica wing' that simulates the foil wing. Load was applied by a hydraulic cylinder.

Eight series of tests were undertaken to simulate the different loads the arms will be subjected to when the AC75 will fly.

The first two tests were performed applying an asymmetric load on the inboard wing to mimic what happens when the outboard end comes out of the water.

Tests number three and four were performed by applying the asymmetric loads to the outboard end using the same strains and cycles (30+) as above.

The fifth test was a bear-away load case and it was performed in order to simulate the maximum cant moment which would happen normally at the top mark.

Test six was an impact load case, to simulate the event of the arm hitting another surface.

The last two tests (7 and 8) were again bear-away load cases, but this time the weight applied was brought to the point where audible noises (test 7) and breakage (test 8) were expected.

To monitor any potential internal damage to the board, the foil arm was covered by microphones and fibre optic strands to record the acoustic emissions and strains at all times. Ultrasound surveys were completed after each test.

The AC75 port and starboard foils are composed of a foil arm and a foil wing.

The AC75 4.5 metre long carbon foil arm has a wing attached to the tip of the arm, which provides the upward force needed to lift the AC75 clear of the water. The foil wing (4 metre span) is custom designed and will be built by each team.

Driving the foil arms is the electronic and hydraulic foil cant system (FCS), another one design supplied part which puts the arms and wings in and out of the water. The foil cant system was designed by Emirates Team New Zealand and manufactured in Auckland.

Related Articles

America's Cup: Class Rule and Tech Regs out
The America's Cup Class Rule and Technical Regulations for the Naples Match have been published With the clock ticking down to the start of the Louis Vuitton 38th America's Cup in Naples in 2027, the AC75 Class Rules and Technical Regulations have been issued to all teams and published with a focus on cost containment. Posted today at 7:18 am
America's Cup: Running silent and deep, again.
A look at the flotsam that has surfaced as the Cup teams again go into deep and silent negotiation. A look at the state of the Cup - given the three weeks of silence since the hasty final Protocol signing. Previously a long deep dive by the teams has indicated that a lot of negotiation is underway. Here's what we've seen floating on the surface. Posted on 10 Sep
From The Other Side - The State of the Sport
The editors of Sail-World New Zealand and Inside Great Lakes Sailing discuss the state of sailing. The Editors of Inside Great Lakes Sailing and Sail-World New Zealand got together last week to shoot the breeze in an unscripted video discussion, without any pre-arranged "talking points" about various aspects of the sport. Posted on 5 Sep
Youth America's Cup set to continue in Naples
The Youth America's Cup is a sign-post to the future direction of the America's Cup itself. Since its inaugural event in 2013, the Youth America's Cup, designed as a competition for sailors under the age of 25, has always been the most remarkable sign-post to the future direction of the America's Cup itself. Posted on 4 Sep
America's Cup: Carlo's insights 1983-2024
Leading Italian lensman Carlo Borlenghi has been shooting the America's Cups for 41 years Carlo Borlenghi is the go-to photographer for many of the world's top sailing events and has covered every America's Cup since 1983 when he was assigned to the Azzurra team for Italy's first challenge. Posted on 30 Aug
America's Cup: A seismic shift for sailing
For the first time in its 174-year history, female sailors will be mandated onboard AC75s This week's announcement from the America's Cup felt momentous. For the first time in its 174-year history, female sailors will be mandated onboard AC75s at the pinnacle of our sport. Posted on 15 Aug
America's Cup: The Brave, New Protocol
The just announced Protocol for the America's Cup has many innovations and a few fish hooks The just announced Protocol for the America's Cup has many innovations, and maybe a few unintended consequences around the mandatory re-use of 2024 vintage AC75 hulls. Updated with a look at how the new Cup structure could work. Posted on 12 Aug
America's Cup: A "ground breaking" partnership
An innovative Protocol for the 2027 America's Cup has been agreed between RNZYS and RYS An innovative 11th hour Protocol for the 2027 America's Cup has been agreed between the Challenger of Record and the Defender. It creates a commercial framework for the current and future Cups, eases nationality rules, and has a quota for female sailors. Posted on 12 Aug
Cup sailor and commentator dies suddenly
A look at the many achievements and contributions of Peter Lester who died suddenly at 70yrs. It seems like only last month that Peter Lester was being carried shoulder high in his OK Dinghy, up Takapuna Beach, having just won the 1977 World championship, having just won the World championship. . Posted on 9 Aug
America's Cup impasse close to resolution.
The impasse over the Protocol is expected to be resolved next week - meeting in Auckland. The impasse over the Protocol for the 38th America's Cup is expected to be resolved, one way or the other, next week, with a meeting of the parties in Auckland. Posted on 9 Aug
PredictWind - Offshore App 728x90 BOTTOMBarton Marine Pipe GlandsLloyd Stevenson - AC Alinghi 1456x180px BOTTOM