Please select your home edition
Edition
Barz Optics - Floaters

Inverter Installation- Troublshooting 101

by Don Wilson on 22 May 2013
Installing our inverter - have you been through this? .. .
So you want to install an inverter, but with all the features and complexity of today’s more sophisticated units, you’re hesitant to take the plunge? Or, perhaps you’ve had some problems with your inverter, and you’re not sure if it’s a faulty unit … or a simple installation problem?

Let the Tech Doctor help! This issue offers up some basic troubleshooting tips to help ensure your inverter is installed correctly in order to deliver maximum, trouble-free delivery. Success in this area will save aggravation and potentially money associated with having to engage a support technician for unwarranted and unnecessary repairs.

Let's get started:

First, an overview. When working with electrical circuits, you must always ensure the circuit is powered down and cannot be re-energized while you are working on it. If you’re not entirely comfortable with this task (or any other cited in this article) then by all means, leave it to the experts. Your attention and compliance to all safety directives must always be first and foremost!

The Basic Benchmark:

If for any reason, things don’t seem to be working as they should with your inverter, understand that these types of products simply don’t 'kind-of' fail. When an inverter goes bad, typically nothing will work … or, one of the features simply won’t work consistently.

Strategies for inverter installation success:

1. Revert all settings to factory defaults.

This may seem obvious, but the factory default settings are usually default for a reason. They are the values that allow the inverter to work in the vast majority of environments. While you don’t want to leave these settings to factory default in the long term, for a quick test, it’s ideal. After completing the test, then you can easily readjust the settings to meet your specific needs. Check the settings, one by one, until the problem is identified, or the settings are adjusted to work. Note: If the inverter came installed with your vehicle/vessel, the manufacturer would likely have changed the factory default settings to custom settings to suit the design and application. In such circumstances, once you reset the inverter to the default OEM/manufacturer setting, you may not need any further changes.

2. Disconnect all loads.

This action will remove the installation as a possible cause of the problem. This is also a good time to disconnect the battery, wait a few minutes, and then reconnect, in order to reboot the inverter’s processor.

3. Power up the inverter.

If this works, bring the loads on-line, one by one.

4. Watch the DC voltage at the inverter and make sure the voltage stays within the DC voltage range of the inverter.

This eliminates the possibility that an ineffective circuit from the battery is causing the issue. If the voltage is erratic, solve that problem by tracing the cause of the erratic voltage and fixing it, and then get back to the inverter. Recommendation: if you don’t have a spare DC fuse on board, get one!

Also, read up on and review the features of your inverter. Some perceived problems actually arise from features in the inverter like idle mode, or power save. Such features, when enabled, allow the inverter to turn off when the load is low, but can create the very real perception of a problem.

Remember: inverters don’t produce energy; they simply convert what they’re given. If you have a combination inverter/charger, and the inverter doesn’t work, but the charger is humming along fine, then check the DC voltage at the inverter when inverting to gauge whether it is within the inverter’s DC range. If the inverter works, but the charger is problematic, then check the AC input voltage at the inverter and ensure it is within the inverter’s AC range. With a sound read of what the unit is receiving, you can eliminate most causes of perceived failure.

A final troubleshooting review:
1. For the most part, inverters either work, or they don’t.

2. From my own experience and in working with dozens of tech service centers, I have concluded that more than 80% of inverters that are returned without hands-on troubleshooting have absolutely no issues on the bench. The problem in at least 20 percent of the returns correlate directly to faulty installations.

3. Erratic behavior, or inconsistent problems, are almost always a loose connection…somewhere. While it’s not easy to find them, it’s worth the time and the effort.

4. A quality volt-meter is worth the investment. While there is a cost associated with ownership, it may pay off in eliminating shipping and diagnostic bench time at the service center that is unnecessary.

5. Safety first!. Power down as much as reasonable when working with circuits. Always use one hand when working with wiring. If you’re not qualified, or are not 100% confident in the process you’re attempting, hire a qualified electrician

Summary:
Remember, inverters are nothing more than an appliance that does what it’s told to do. If it doesn’t receive the right instructions, or can’t interpret its input, it likely will not perform to your expectations, through no fault of its own. Take the time to ensure the proper installation in order to maximize the performance of your hard-working inverter! Then, you will realize its ultimate return on investment.

Sail-World Cruising would like to thank www.xantrex.com!Xantrex_Technology for this informative article
Wildwind 2016 660x82Barz Optics - FloatersAncasta Ker 33 660x82

Related Articles

2014 J/24 World Championship - Will Welles’ Cougar clinches
Welles had used his throw-out on Thursday, so the only way to assure a win was to stay ahead. 2014 J/24 World Championship - With just a few points between Will Welles Cougar (USA) and Mauricio Santa Cruz Bruschetta (BRA) there was no room for error in the final two races of the 2014 J/24 World Championship hosted by Sail Newport.
Posted on 27 Sep 2014
J/24 World Championship - Will Welles hangs on going into last day
The Race Committee chose to sail inside north of the Newport Bridge for races seven and eight of the 2014 J/24 Worlds. With marginal conditions and diminishing visibility on the ocean course, the Race Committee chose to sail inside north of the Newport Bridge for races seven and eight of the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) sailed his throw-out in race seven but came back with a solid six in race eight to hold onto the lead with a total score of 31 points.
Posted on 26 Sep 2014
2014 J/24 World Championship - Will Welles holds advantage
After a struggle to set the line square to the shifting wind, the fleet got off two more races at 2014 J/24 World Champ 2014 J/24 World Championship - After a struggle to set the line square to the shifting wind, the fleet got off two more races at the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) held the lead with a four, four respectively for a total score of 16 points.
Posted on 25 Sep 2014
2014 J/24 World Championship - Will Welles takes lead
Teams battled today in more stable sea conditions on ocean course in wind speeds from 10 to 14 knots out of southwest. 2014 J/24 World Championship - After a morning postponement ashore, the fleet got off two more races at the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) moved to the lead with a nine, one respectively.
Posted on 24 Sep 2014
J/24 Worlds - Opening day leaves two teams tied on points for lead
Newport, Rhode Island welcomed 70 teams from around the globe with wind and waves on the first of five days 2014 J/24 World Championship - Newport, Rhode Island welcomed 70 teams from around the globe with wind and waves on the first of five days at the 2014 J/24 World Championship. The top of the fleet saw some familiar names but also some fresher faces. Mark Hillman’s Sokokumaru (USA) and Vernon Robert’s Gringa DC (Chile) are tied at five points, with Hillman having the first-place advantage thanks to
Posted on 23 Sep 2014
J/24 World Championship - Excitement builds for Newport racing
Seventy-one teams from 13 nations are registered to compete in the 2014 J/24 World Championship. The legend lives on 37 years after Rod Johnstone built the first J/24. Seventy-one teams from 13 nations are registered to compete in the 2014 J/24 World Championship in Newport, Rhode Island.
Posted on 19 Sep 2014
Rather clean your own hull - or sailing remotely? here's a solution
If you'd rather clean your own hull here's a new product that you should consider when making a decision. If you'd rather clean your own hull, or need to because of where you intend to be sailing, here's a new product that you should consider when making a decision. Its initial selling price maybe high, but in a year or two, by avoiding that expensive yearly haul-out, you'll be way ahead.
Posted on 23 Jul 2013
World's tiniest PLB now certified for use
Ocean Signal's rescueME PLB1, the tiniest PLB in the world, has now been certified for use in Europe and the USA The tiniest PLB in the world, introduced to the sailing world in January, has now been fully certified for use throughout Europe and the USA after being awarded relevant COSPAS-SARSAT and product approvals. The product will be available in Australia after being launched later this month.
Posted on 5 Apr 2013
Checking your rigging
The best fertiliser on a farm is the farmer's footsteps, and the best insurance for your mast is the eye of the skipper Just as they say the best fertiliser on a farm is the footsteps of the Farmer, so the best insurance for your mast is the eye of the skipper. This means regular checks before any major voyage. However, when it comes to a thorough check, the only way of ensuring you have found every fault is to remove the rig.
Posted on 22 Feb 2013
Innovative thinking leads to new Tandem Anchor product
Nominated for a DAME design award in 2012 is the tandem anchor system - two anchors, but only one chain If you are in love with the idea of putting out two anchors when the going gets tough, you may like the idea of a new idea in anchoring which was nominated for a DAME design award in 2012. It's the tandem anchor system - two anchors, but only one chain and it comes from a brand new company making waves for their innovative designs.
Posted on 17 Nov 2012