New Posts New Posts RSS Feed: Topper Bailer Blanking Plate
  FAQ FAQ  Forum Search   Register Register  Login Login

Topper Bailer Blanking Plate

 Post Reply Post Reply
Author
llywelyn1984 View Drop Down
Newbie
Newbie


Joined: 31 Jan 18
Online Status: Offline
Posts: 9
Post Options Post Options   Quote llywelyn1984 Quote  Post ReplyReply Direct Link To This Post Topic: Topper Bailer Blanking Plate
    Posted: 30 Apr 18 at 3:58pm
My allen self bailed on my topper leaks, either through the plunger part or somewhere else. 

I have bought a topper blanking plate. 

Does anyone know how to fit it?

Andrew
Back to Top
Sam.Spoons View Drop Down
Really should get out more
Really should get out more


Joined: 07 Mar 12
Location: Manchester UK
Online Status: Offline
Posts: 2141
Post Options Post Options   Quote Sam.Spoons Quote  Post ReplyReply Direct Link To This Post Posted: 30 Apr 18 at 9:42pm
I haven't seen one but does it not just replace the bailer? The bailer is fixed by 6 nuts and bolts, there is a rubber gasket between it and the hull and a rebate on the hull so it sits flush. There should be no need for any sealant if the new gasket (which I assume os supplied with the blanking plate......) is in good order.
Spice 346 "Flat Broke"
Blaze 671 "supersonic soap dish"
Back to Top
GML View Drop Down
Groupie
Groupie


Joined: 24 Jul 11
Online Status: Offline
Posts: 79
Post Options Post Options   Quote GML Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 18 at 8:14am
Some blanking plates fit into the bailer housing in place of the chute. Undo the screws that hold the top and bottom halves of the bailer together; remove the chute assembly; replace with the blanking plate; screw it all back together again. I believe it can be done whilst the bailer is still in the boat, but probably easier if you take it out of the boat first. Following pictures and words from Rooster Sailing might help: http://www.roostersailing.com/blog/maintain-and-repair-your-topper-bailer/

Edited by GML - 01 May 18 at 8:14am
Back to Top
llywelyn1984 View Drop Down
Newbie
Newbie


Joined: 31 Jan 18
Online Status: Offline
Posts: 9
Post Options Post Options   Quote llywelyn1984 Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 18 at 4:00pm
Thanks both, 
It's the older allen bailer, im going to have a look tonight and see what's what. 
Ive had duck tape over the bottom which has lasted a surprisingly long time but during a race last week she started filling up slowly! 
Back to Top
Wiclif View Drop Down
Groupie
Groupie
Avatar

Joined: 04 Oct 05
Location: United Kingdom
Online Status: Offline
Posts: 48
Post Options Post Options   Quote Wiclif Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 18 at 5:04pm
All the answers assume that it is the Super Chute bailer, and your blanking plate is almost certainly for that.

The older Allen bailer was very different. I think it may still possible to get that bailer from Allen though it is a couple of years since i tried. You used to be able to buy it with or without the stainless steel guard and one of those options was discontinued. However, the Allen bailer does not have a non return flap, which limits its appeal. Your practical answer is probably to make your own blanking plate to replace the bailer. Make sure that the hull to deck join is properly sealed at the bailer hole.
Back to Top
423zero View Drop Down
Really should get out more
Really should get out more


Joined: 08 Jan 15
Location: United Kingdom
Online Status: Offline
Posts: 1543
Post Options Post Options   Quote 423zero Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 18 at 5:09pm
Why not just re-seal existing or fit new bailer, your race is over if you capsize.
Back to Top
Rupert View Drop Down
Really should get out more
Really should get out more


Joined: 11 Aug 04
Location: Whitefriars sc
Online Status: Offline
Posts: 8180
Post Options Post Options   Quote Rupert Quote  Post ReplyReply Direct Link To This Post Posted: 01 May 18 at 8:41pm
I bought an Allen Gold bailer a few months ago.

Oddly, capsizing can be the only way of emptying the boat if you get swamped and have no bailer. A cut down plastic milk bottle tied in can work well, though.
Firefly 2324, Lightning 130, Puffin 229, Minisail 3446
Back to Top
llywelyn1984 View Drop Down
Newbie
Newbie


Joined: 31 Jan 18
Online Status: Offline
Posts: 9
Post Options Post Options   Quote llywelyn1984 Quote  Post ReplyReply Direct Link To This Post Posted: 02 May 18 at 10:09am
hi guys,

Thanks for your input, I searched everywhere to no avail on the net!

I had a look a couple of the club boats yesterday and they have blanking plates, but indeed do look a bit different.

I managed to buy a rebuild kit for the allen bailer. I have replaced the plunger seal which was absolutely shot, however I haven't been able to test it yet. There was also a gasket seal in the kit, but I haven't fitted this yet.

If this fails I will go back to my duck tape. Well actually it's a product called Maxam glass repair film. I was astonished at how well it was still stuck on when I took it off yesterday considering ive sailed with it on 7 or 8 times and I always drag my boat up the slip way.

I tried the milk bottle cut in half but I didn't tie it on, so it's now at the bottom of the sea somewhere, sorry david Attenborough!

It seems mad to spend 50 on a boat which cost me 220.
Back to Top
 Post Reply Post Reply

Forum Jump Forum Permissions View Drop Down

Bulletin Board Software by Web Wiz Forums® version 9.665y
Copyright ©2001-2010 Web Wiz
Change your personal settings, or read our privacy policy