News Home Video Gallery Newsletters Photo Gallery Cruising Int
Sail-World.com : Checking your rigging
Checking your rigging


'The best insurance is the eye of the skipper'    .

Just as they say the best fertiliser on a farm is the footsteps of the Farmer, so the best insurance for your mast is the eye of the skipper. This means regular checks before any major voyage. However, when it comes to a thorough check, the only way of ensuring you have found every fault is to remove the rig.

An aluminium rig will last in good condition for many years, and it pays to find out what your insurance company considers reasonable before replacement. Having said that, corrosion and fatigue can creep up unexpectedly if there is not a regular checking routine. And it could be merely a cracked turnbuckle or a corroded clevis pin which brings your mast down when you least expect it.

Checking the rigging - Taking the mast out of some boats is easier than others -  .. .  

What to look out for:
Generally the most important thing is to be on the lookout for cracks and corrosion. If the rig is painted, watch for bubbles in the paint, a sure sign of corrosion. If it's anodized, watch for a white, powdery residue. Sometimes potential problems can stay hidden unless you remove the rig from the boat, so, between checks it will be the tiny clues that you are searching for.

Checking the rigging on land is the only way to be thorough -  .. .  
Mast cap:
Closely examine the cap for corrosion, cracks, and wear. Remove the backstay and forestay fittings and inspect where they attach to the cap. If the holes show excessive wear-such as a groove in the bottom of the hole-or have elongated, the cap needs to be repaired. Clevis pins should be straight and just wide enough to fit through the holes. If the pin is too thin or too long, it may bend or crack. It's best to replace all undersized pins and all cotter pins. Never replace a clevis pin with a bolt. A bolt's threads simply act like a file.

Check toggles for cracks and corrosion and for proper alignment. Remove all shackles and blocks. Inspect them for cracks, corrosion, and chafe.

Make sure that the antennas, lights, and wind instruments are functioning and that all wires are sufficiently protected against chafe. A chafed wire not only leads to a faulty masthead light; any stray current, even from something so small, can, when combined with water and salt, speed up rig corrosion dramatically.

Don't forget the halyard sheaves. Make sure they run free and check the axle pin for cracks and wear.

The Mast:
As you work your way down the mast, keep an eye out for corrosion, chafed areas, cracks, and dents in the mast extrusion itself. Even a small dent can weaken a mast enough to make it buckle. If your mast consists of two extrusions spliced together, make sure that the splice is tight, straight, and free of loose or corroded fasteners.

Shrouds:
Chances are that a shroud will fail where it attaches to something, so shroud tangs and T-ball sockets, which are crucial to the integrity of the whole system and subject to high loads and fatigue, deserve special attention. It's important to inspect the tangs and T-ball sockets for corrosion and cracking where they connect to the mast. Keep an eye out for corroded or distorted fasteners, and make sure that all stainless-steel fittings are sufficiently isolated from an aluminum mast. It's also critical to make sure that tangs and T-ball sockets are well reinforced and accept the shroud at the proper angle. A misaligned tang or weak T-ball socket can cause a shroud to fail.

Spreaders: Spreaders are designed to withstand compression loads, but for them to function properly, the angle that a spreader forms with the shroud must be 90 degrees, i.e., equal both above and below the spreader. A cracked, bent, or overly worn spreader is a good clue that it was probably misaligned and needs to be repaired or replaced.

Check for cracks, wear, and corrosion in the spreader bases and check for excessive play in the spreader. It's a good idea to remove the bases to verify the condition of the interior of the mast wall and of the compression tube running through the mast.

Spreader tips are another common trouble spot. They're subject to extreme load fluctuations and are usually covered with chafe guards that can trap water and starve the stainless steel of oxygen-a perfect recipe for corrosion. Make sure to remove the chafe guards and thoroughly inspect the spreader tips.

Mast step:
Because of its proximity to the bilge, a keel-stepped mast is highly susceptible to corrosion. Improper mast drainage and any loose current from a frayed wire can also contribute to corrosion of both the bottom of the mast and the step itself. Excessive corrosion could indicate one or all of these problems.
Keel-stepped masts are also susceptible to corrosion where the mast passes through the deck. Check for cracks and wear under the mast boot.

Deck-stepped masts aren't as prone to corrosion at the base as keel-stepped masts, but it's still important to check for cracks, corrosion, and proper drainage and to make sure that the deck isn't deformed.

Standing rigging:
With wire rigging, cracked swages (fittings compressed onto the wire under high pressure) are a common cause of rig failure, so make sure to check that each swaged fitting is straight and free of cracks and corrosion. Water and salt running down the wire and seeping into the fitting can speed up swage corrosion, so even if the fitting is free of cracks, be on high alert for corrosion near the top of the fitting. It could be an indication that the interior of the fitting has started to corrode and may be untrustworthy. Mechanical or swageless compression fittings like those made by Norseman and Staylock are generally more durable than swaged fittings, but these still should be checked periodically.

Then check the turnbuckles. Make sure each is straight and free of corrosion and cracks. All turnbuckles should be clean and lubricated, and should be secured with brand-new split rings or cotter pins.

Then check the wire for corrosion and broken strands. Just one broken strand can make the wire untrustworthy.

Chainplates:
Water and salt often get trapped between the chainplates and the deck, where corrosion is difficult to detect. If the chainplate seal is broken or you see evidence on the inside of the boat that water is seeping down the chainplates, chances are that the chainplates could be corroded and will need some special attention.

It's not worth going to the trouble of doing the checks unless you replace anything that is even slightly suspect. You'll sleep better at night in a storm when you know that your mast is in the best possible condition and your on-deck crew are safe from falling masts.


by Des Ryan

  

Click on the FB Like link to post this story to your FB wall

http://www.sail-world.com/index.cfm?nid=106823

11:28 PM Thu 21 Feb 2013GMT


Click here for printer friendly version
Click here to send us feedback or comments about this story.

Click for further information on
Practical

Related News Stories:

24 Feb 2013  Product of the Week: Removable sailing pouches
24 Feb 2013  Product of the Week: Removable sailing pouches
19 Feb 2013  Cruising Association's mobile App, going gangbusters
18 Feb 2013  West Marine's 'Green Products of 2013' announced - both practical
15 Feb 2013  Autopilots - about to get more 'intelligent'
15 Feb 2013  Autopilots - about to get more 'intelligent'
11 Feb 2013  Fire onboard!
10 Feb 2013  Green antifouling technology - getting better every year
10 Feb 2013  Cruising sailors and iPads - One tech-savvy cruising sailor tells
10 Feb 2013  Cruising sailors and iPads - One tech-savvy cruising sailor tells
MORE STORIES ...






Cruising USA







Barnacle Busting by Neil and Ley Langford,


From Penguins to Polar Bears by Cherie Winner,




Polar research: Six priorities for Antarctic science by Mahlon C. Kennicutt II and colleagues,




NCI granted dedicated VHF Channel by National Coastwatch,


Positive news for cruising boats in Greece by The Cruising Association,




















Risks to penguin populations continues by British Antarctic Survey,




Follow these tips when anchoring by Alex and Daria Blackwell,


Galley Guys meet the Spice Lady by Greg Nicoll, Andy Adams and John Armstrong,




If all else fails read the instructions!! by Stuart Carruthers, RYA Cruising Manager,




Phuket Yacht Show: new kid on the block taking on PIMEX? *Feature by Guy Nowell, Sail-World Asia and Phuket Yacht Show,






Flags at Sea, an infographic by John Tissott by Anna Parker and the Sail-World Team,








Teen names latest RNLI Shannon class lifeboat in Poole + Video
Fascinating opportunity with OceansWatch
Fake GPS signals detected when cruising the high seas
Our new Cruising Editor editor remembers his first offshore adventure
Blue Planet Odyssey - Jimmy Cornell playing catch up on North West Pa
World ARC 2014 reaches Australia
Venezuelan Port Control lift recent port restrictions.
Seismic survey ship operating north of Aruba and Curacao
Predictwind helps you pick the best time to depart
Watch this whale lift a Kayak clear out of the water
World ARC reaches half-way point in Australia
Northern Scotland: Voyage to Orkney and Shetland Isles (Part 2) *Feature
Drowning or electric shock? What you need to know to help save a life
Costa Concordia - the $2.25 billion salvage operation ready to begin
Northern Scotland: Voyage to Orkney and Shetland Isles, more photos *Feature
Fort Lauderdale International Boat Show - New location and attractions
Long Island waters could become more taxing this summer
4.8 million Legos all at sea
Tranquil, colourful and funky, Genoa Bay is a must stop for West Coast *Feature
Scientist pioneered tracer to reveal hidden ocean flows
Sail-World 2.0 - the Beta version- Please take a look   
Dredging activity near corals can increase frequency of diseases   
World ARC heading out of the Pacific   
Understanding the Ocean's role in Greenland Glacier melt   
Desolation Sound added to Salish Sea Pilot free cruising guides   
Three Defensive Docking Strategies for Sailors   
Revealing report on Search for American yacht Nina released *Feature   
PredictWind's Weather Routing opens your navigation options - try it!   
Sail-World Cruising Founding Editor Nancy Knudsen says farewell   
Book review: Weather - you like it or not   
Vaavud launches generation 2 wind meter   
The drama begins - North West Passage sailors rescued from ice   
Entering an unfamiliar bay - decision time   
Baby Nemos finding their way home   
High Latitude Sailing - Book of the Week   
Will the Olympics make a difference to Rio pollution? *Feature   
Blue Planet Odyssey, around world rally, begins   
Africa Europe Cruising Challenge now open for entries   
The real ‘Supermoon’ story   
Warm and noisy welcome for Oceans of Hope in La Rochelle   


For this week's complete news stories select    Last 7 Days
   Search All News
For last month's complete news stories select    Last 30 Days
   Archive News







Sail-World.com  


















Switch Default Region to:

Social Media

Asia

Australia

Canada

Europe

New Zealand

United Kingdom


http://www.sail-world.com/event_images/image/Twitter_logo_small.png http://www.sail-world.com/event_images/image/FaceBook-icon.png  

United States

Cruising Northern

Cruising Southern

MarineBusiness World

PowerBoat World

FishingBoating World

 

Contact

Commercial

News

Search

Contact Us

Advertisers Information

Submit news/events

Search Stories/Text

Feedback

Advertisers Directory

Newsletter Archive

Photo Gallery

 

Banner Advertising Details

Newsletter Subscribe

Video Gallery

Policies

 

 

 

Privacy Policy

 

 


Cookie Policy

 

 



This site and its contents are © Copyright TetraMedia and/or the original author, photographer etc. All Rights Reserved.  Photographs are copyright by law.  If you wish to use or buy a photograph contact the photographer directly.
XLXL NEW Cru USA
LocalAds   DE  ES  FR  IT