Please select your home edition
Edition
Ancasta Ker 33 728x90

Preparing the boat

by Cruising Editor on 22 Nov 2005
Whether you're preparing for a journey, or just preparing your boat for the season, check-lists are excellent for making sure you don't forget a vital task

Here is a the most comprehensive check-list I’ve read of things you should at least consider before leaving port – it’s an American site, but quite useful, called http://www.boatsafe.com/nauticalknowhow/spring99.htm!Boatsafe!same

There’s also a pretty good checklist in the Boat Bible (which is also good for other information), by Jim Murrant, and published by Sheridan House. See your local marine shop, or refer to Boatbooks

The all important engine:
This is the run-down on what should be done to your diesel engine before going on a long trip. Even if you don’t do the work yourself, it’s a good indication of what you need to tell your diesel engineer you want done. DON’T assume that ‘he knows what to do’.

This information has been provided by Laurence Burgin, of Marine Stainless in Sydney. Laurence also runs excellent one day workshops for those who want to know more, and be able to troubleshoot when help is not near.


PRE-SEASON ENGINE CHECKS

Fuel Tanks
· Check breather hose and outlet is not blocked
· Check tank is securely mounted
· Ensure fuel lines are good quality
· Check for bacterial growth after sea trial – growth lies in base of tank so give it a shake up first (as a storm would)
· Drain or pump fuel from base of tank to ensure no water or contamination
· Clean fuel is essential – don’t go to sea with bad fuel

Fuel
· Ensure there is enough fuel in tank for intended passage, plus a healthy reserve
· Check fuel shut off valves are in good condition
· Replace primary fuel filter for water or contamination – drain water till clear
· Check no fuel leaks from system in operation
· Get to know lift pump operation
· Replace engine filter
· Test bleed engine at anchor so you will be able to do it at sea

Cooling
· Check water inlet valve is in good condition
· Check raw water strainer is clean – remove strainer basket and clean if needed
· Check coolant level in header tank, top up if needed. (Where did it go?) Carry good quality spare coolant
· Check hoses and clamps for wear, looseness or leaks – replace if in doubt

Oil
· Dip sump and check oil level – top up if necessary. Change oil and filter every 100 hours or 6 months
· Check gear box oil level – some hydraulic boxes need the engine idling in neutral to check oil
· Always carry spare engine and gearbox oil and filters

Electrics
· Turn on battery switches and check operation of switch mechanism
· Check battery hold down system is heavy duty (not just a plastic box with a crappy strap)
· Check all battery and engine wiring for loose connections – put your hand on and see if they rattle (engine off!)
· Clean terminals and grease
· Load test batteries

Belts
· Check belts for correct tightness (12mm or 1/2” deflection on longest run) and alignment
· Check pulleys for rust and running true
· Check for belt wear and carry correct spares

Throttle Box
· Check operation of throttle and gear change – replace control cables if needed (cheap compared to ramming dock!)
· Grease throttle box (remove from boat) and linkages on box and engine
· Learn how to remove cables from engine for jury rig throttle

Do a sea trial with your motor
Give engine a good hard run (80% revs) for at least 10 minutes pushing into wind and sea/current, look at engine during this time
· Be aware of unusual noises, vibrations or smells
· Check for leaks – fuel, cooling or oil
· Check steering operation
· Check oil pressure gauge, temperature gauge, voltmeter for charging
· Make visual checks of engine for leaks, loose ancillary equipment
· Check stern gland for excessive leaking or overheating
· Keep an eye on fuel consumption – know the hourly consumption under load
· Check other equipment

Engine Mounts/drive system
· Check for worn or broken mounts
· Check engine alignment is good
· Check stern bearing and shaft not worn (slipway or dive)
· Check flexible coupling is in good condition
· If there are any doubts about the mounts have them changed
· Check propeller is tight and foul free (Prop speed is the go)

Exhaust
· Check engine exhaust dropper for blockage and excessive corrosion (a common problem)
· Check all hoses and clamps are in top condition
· Make sure your exhaust system is correctly designed and installed to prevent water backflow from wave action or syphon effect. Many systems are not up to passage making standards
· Have you a syphon break installed in system?

Heat Exchanger
· Bi-annual removal and inspection of your cooling core (the boat’s radiator) for blockage
· Check anodes for wear, replace and carry spares

Impeller pumps – raw water
· Remove and replace the impeller in the engine (know how to do this yourself)
· Check oil seals if direct drive pump
· Carry spares

Starter
· Annually remove starter motor and have serviced



Spares – a complete list of recommended spares is available in available from Marine Diesel Engines for Beginners

Alternator
· Regularly remove alternator and have serviced. For long range cruising carry a spare

Tools
· Carry good quality tools and have engine manuals on board

TOOLS YOU MUST HAVE – Inshore tool kit
(store in a strong plastic box)
Quality screwdriver set
Bahco quality hacksaw 2 x Bahco hacksaw blades
Heavy ballpein or lump hammer Rubber hammer
Metric & imperial Allen key sets—fold-up type Torx driver kit
Linesman’s pliers Long nose pliers
1 pair vice-grips—Genuine! Model I0 WR Oil filter strap wrench
Side cutters 18½ Stilsons
4½–6½ & 12½ shifters Razor knife and spare blades
1 set metric & imperial combo spanners Small bolt and screw kit
3/8½ sockets (small engine)(Must come in a plastic box – look around) 1/2½ Sockets (large engines)
Lanoline grease or spray Round and flat file—Bahco
Vice grips style electrical crimp pliers & crimp lugs Wire brush
1/4½ pin punch Hose clamp driver
Liquid paper pen for marking 12½ steel ruler

EXTRA TOOLS YOU SHOULD HAVE – Offshore tool kit
(store in another strong plastic box)

Large parrot-beak cutters (not bolt cutters) Multi metre
T-Bar tap holder Hose clamp driver
Soldering Iron 18½ shifter
12½ Stilsons Another pair of vice grips
Small Vice to bolt or clamp somewhere 1/4½ socket set
12volt Cordless Drill / Torch Combo plus as many batteries as you can store and, ideally, the ability to recharge batteries Drill bit index—quality
Extensive bolt kit Wire strippers
3/16½ Pin Punch Center punch
1 m Steel Rule Bahco file set
Tube Cutters Large multi-grips
Tin Snips Engine workshop manual
Quality rigging knife in scabbard

and don't forget the...
BOTTLE OF RUM!

Newport Boat Show 2016 660x82T Clewring AC72Barz Optics - Melanin Lenses

Related Articles

2014 J/24 World Championship - Will Welles’ Cougar clinches
Welles had used his throw-out on Thursday, so the only way to assure a win was to stay ahead. 2014 J/24 World Championship - With just a few points between Will Welles Cougar (USA) and Mauricio Santa Cruz Bruschetta (BRA) there was no room for error in the final two races of the 2014 J/24 World Championship hosted by Sail Newport.
Posted on 27 Sep 2014
J/24 World Championship - Will Welles hangs on going into last day
The Race Committee chose to sail inside north of the Newport Bridge for races seven and eight of the 2014 J/24 Worlds. With marginal conditions and diminishing visibility on the ocean course, the Race Committee chose to sail inside north of the Newport Bridge for races seven and eight of the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) sailed his throw-out in race seven but came back with a solid six in race eight to hold onto the lead with a total score of 31 points.
Posted on 26 Sep 2014
2014 J/24 World Championship - Will Welles holds advantage
After a struggle to set the line square to the shifting wind, the fleet got off two more races at 2014 J/24 World Champ 2014 J/24 World Championship - After a struggle to set the line square to the shifting wind, the fleet got off two more races at the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) held the lead with a four, four respectively for a total score of 16 points.
Posted on 25 Sep 2014
2014 J/24 World Championship - Will Welles takes lead
Teams battled today in more stable sea conditions on ocean course in wind speeds from 10 to 14 knots out of southwest. 2014 J/24 World Championship - After a morning postponement ashore, the fleet got off two more races at the 2014 J/24 World Championship hosted by Sail Newport. Will Welles’ Cougar (USA) moved to the lead with a nine, one respectively.
Posted on 24 Sep 2014
J/24 Worlds - Opening day leaves two teams tied on points for lead
Newport, Rhode Island welcomed 70 teams from around the globe with wind and waves on the first of five days 2014 J/24 World Championship - Newport, Rhode Island welcomed 70 teams from around the globe with wind and waves on the first of five days at the 2014 J/24 World Championship. The top of the fleet saw some familiar names but also some fresher faces. Mark Hillman’s Sokokumaru (USA) and Vernon Robert’s Gringa DC (Chile) are tied at five points, with Hillman having the first-place advantage thanks to
Posted on 23 Sep 2014
J/24 World Championship - 35th anniversary preview
Back in 1979, no one would ever imagine the J/24 class would achieve such enthusiastic support and popularity. Back in 1979, no one would ever imagine the J/24 class would achieve such enthusiastic support and popularity that in its first World Championships in Newport, RI, hosted by Ida Lewis YC and sponsored by Bacardi Rum, that 69 boats would participate in that event.
Posted on 20 Sep 2014
J/24 World Championship - Excitement builds for Newport racing
Seventy-one teams from 13 nations are registered to compete in the 2014 J/24 World Championship. The legend lives on 37 years after Rod Johnstone built the first J/24. Seventy-one teams from 13 nations are registered to compete in the 2014 J/24 World Championship in Newport, Rhode Island.
Posted on 19 Sep 2014
World's tiniest PLB now certified for use
Ocean Signal's rescueME PLB1, the tiniest PLB in the world, has now been certified for use in Europe and the USA The tiniest PLB in the world, introduced to the sailing world in January, has now been fully certified for use throughout Europe and the USA after being awarded relevant COSPAS-SARSAT and product approvals. The product will be available in Australia after being launched later this month.
Posted on 5 Apr 2013
Low DSC connect rate-Sailor irresponsibility or technological failure?
Is the low take-up of available DSC connection to radio because of sailor irresponsibility, or is it more complex? Recently we published a story about how few yachts had their Digital Selective Calling (DSC) equipped VHF radio connected to their GPS so that their position would be recorded in an emergency. The tone of the article suggested that the low take-up was an indication of the irresponsibility of sailors, but responses to Sail-World after the article suggest that the situation is more complex than this
Posted on 27 Mar 2011
Sailor's aid or sailor's nightmare - the tides explained
It's not surprising if you don't exactly understand tides - it took a lot of figuring out over the ages As sailors, we all know that tides come twice a day, vary according to the moon, and, depending on where you are sailing are either unimportant, reasonably important, or critically important to a successful completion of your voyage. But why the moon? and if the moon only circles the earth once a day, why are there two tides? Here, Grant Headifen of Nauticed, explains
Posted on 18 Sep 2010