Sail-World.com  Wednesday 01 October 2014

Home Graphical | News Text | Powerboat-World | BoatsPlus | MarineBusiness | SW Aus | Cruising Int | Magnetic Is RW | Photo Gallery | FishingBoating | Newsletter Subscription Here | Search Sail-World


sail-world.com -- Checking your rigging

Checking your rigging    
Fri, 22 Feb 2013

Just as they say the best fertiliser on a farm is the footsteps of the Farmer, so the best insurance for your mast is the eye of the skipper. This means regular checks before any major voyage. However, when it comes to a thorough check, the only way of ensuring you have found every fault is to remove the rig.

An aluminium rig will last in good condition for many years, and it pays to find out what your insurance company considers reasonable before replacement. Having said that, corrosion and fatigue can creep up unexpectedly if there is not a regular checking routine. And it could be merely a cracked turnbuckle or a corroded clevis pin which brings your mast down when you least expect it.


What to look out for:
Generally the most important thing is to be on the lookout for cracks and corrosion. If the rig is painted, watch for bubbles in the paint, a sure sign of corrosion. If it's anodized, watch for a white, powdery residue. Sometimes potential problems can stay hidden unless you remove the rig from the boat, so, between checks it will be the tiny clues that you are searching for.

Mast cap:
Closely examine the cap for corrosion, cracks, and wear. Remove the backstay and forestay fittings and inspect where they attach to the cap. If the holes show excessive wear-such as a groove in the bottom of the hole-or have elongated, the cap needs to be repaired. Clevis pins should be straight and just wide enough to fit through the holes. If the pin is too thin or too long, it may bend or crack. It's best to replace all undersized pins and all cotter pins. Never replace a clevis pin with a bolt. A bolt's threads simply act like a file.

Check toggles for cracks and corrosion and for proper alignment. Remove all shackles and blocks. Inspect them for cracks, corrosion, and chafe.

Make sure that the antennas, lights, and wind instruments are functioning and that all wires are sufficiently protected against chafe. A chafed wire not only leads to a faulty masthead light; any stray current, even from something so small, can, when combined with water and salt, speed up rig corrosion dramatically.

Don't forget the halyard sheaves. Make sure they run free and check the axle pin for cracks and wear.

The Mast:
As you work your way down the mast, keep an eye out for corrosion, chafed areas, cracks, and dents in the mast extrusion itself. Even a small dent can weaken a mast enough to make it buckle. If your mast consists of two extrusions spliced together, make sure that the splice is tight, straight, and free of loose or corroded fasteners.

Shrouds:
Chances are that a shroud will fail where it attaches to something, so shroud tangs and T-ball sockets, which are crucial to the integrity of the whole system and subject to high loads and fatigue, deserve special attention. It's important to inspect the tangs and T-ball sockets for corrosion and cracking where they connect to the mast. Keep an eye out for corroded or distorted fasteners, and make sure that all stainless-steel fittings are sufficiently isolated from an aluminum mast. It's also critical to make sure that tangs and T-ball sockets are well reinforced and accept the shroud at the proper angle. A misaligned tang or weak T-ball socket can cause a shroud to fail.

Spreaders: Spreaders are designed to withstand compression loads, but for them to function properly, the angle that a spreader forms with the shroud must be 90 degrees, i.e., equal both above and below the spreader. A cracked, bent, or overly worn spreader is a good clue that it was probably misaligned and needs to be repaired or replaced.

Check for cracks, wear, and corrosion in the spreader bases and check for excessive play in the spreader. It's a good idea to remove the bases to verify the condition of the interior of the mast wall and of the compression tube running through the mast.

Spreader tips are another common trouble spot. They're subject to extreme load fluctuations and are usually covered with chafe guards that can trap water and starve the stainless steel of oxygen-a perfect recipe for corrosion. Make sure to remove the chafe guards and thoroughly inspect the spreader tips.

Mast step:
Because of its proximity to the bilge, a keel-stepped mast is highly susceptible to corrosion. Improper mast drainage and any loose current from a frayed wire can also contribute to corrosion of both the bottom of the mast and the step itself. Excessive corrosion could indicate one or all of these problems.
Keel-stepped masts are also susceptible to corrosion where the mast passes through the deck. Check for cracks and wear under the mast boot.

Deck-stepped masts aren't as prone to corrosion at the base as keel-stepped masts, but it's still important to check for cracks, corrosion, and proper drainage and to make sure that the deck isn't deformed.

Standing rigging:
With wire rigging, cracked swages (fittings compressed onto the wire under high pressure) are a common cause of rig failure, so make sure to check that each swaged fitting is straight and free of cracks and corrosion. Water and salt running down the wire and seeping into the fitting can speed up swage corrosion, so even if the fitting is free of cracks, be on high alert for corrosion near the top of the fitting. It could be an indication that the interior of the fitting has started to corrode and may be untrustworthy. Mechanical or swageless compression fittings like those made by Norseman and Staylock are generally more durable than swaged fittings, but these still should be checked periodically.

Then check the turnbuckles. Make sure each is straight and free of corrosion and cracks. All turnbuckles should be clean and lubricated, and should be secured with brand-new split rings or cotter pins.

Then check the wire for corrosion and broken strands. Just one broken strand can make the wire untrustworthy.

Chainplates:
Water and salt often get trapped between the chainplates and the deck, where corrosion is difficult to detect. If the chainplate seal is broken or you see evidence on the inside of the boat that water is seeping down the chainplates, chances are that the chainplates could be corroded and will need some special attention.

It's not worth going to the trouble of doing the checks unless you replace anything that is even slightly suspect. You'll sleep better at night in a storm when you know that your mast is in the best possible condition and your on-deck crew are safe from falling masts.

by Des Ryan



Our advertisers are committed to our sport, please support them! (Graphics)
Contact us , ph: +61 2 8006 1873, , fax: +61 2 8076 0459 or complete our feedback form. View our Privacy Policy. Photographs are copyright by law, if you wish to use a photograph from www.sail-world.com, please Contact us. [Go Home(Graphics)]
Make sail-world.com Australia my default page.    Make sail-world.com Cruising International my default page.  Make sail-world.com Cruising Australia my default page.  Make sail-world.com Asia my default page.   Make sail-world.com New Zealand my default page.   Make sail-world.com UK my default page.   Make sail-world.com USA my default page.  


Visit another region : Sail-World Australia    Sail-World Cruising International   Sail-World Cruising Australia   Sail-World Asia   Sail-World New Zealand   Sail-World UK   Sail-World USA  

Onesails.com - Workforce
OneSails is the culmination of over 35 years of experience accumulated by our team in design and technology applied to sail-making.
[More info]
http://www.onesails.com

GME Standard Communications Pty Ltd
Leaders in communications and navigation. Their goal has always been to make products whose innovation, convenience and peace of mind can help improve the lives of their customers.
[More info]
http://www.gme.net.au

VicSail Sydney
Vicsail Sydney Pty Ltd, launched into the Australian sailing fraternity in 1983 and has been sailing strong ever since. At Vicsail, “We Sail the Boats We Sell”.
[More info]
http://www.vicsailsydney.com.au